 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ADSL CPE Hybrid APC78106 OPERATING TEMPERATURE -40C TO +85C FEATURES * APC78106 is designed to interface with Alcatel's MTK20150 and MTK20141 ADSL transceiver chip sets to optimize customer premises equipment (CPE) designs. The Hybrid contains every component required between the analog front end chip and the connector including the line interface transformer and common mode chokes, line protection circuitry, transmit and receive filters (excluding line driver and parallel capacitors). The hybrid was designed jointly by APC and Alcatel to optimize the transmission capabilities of the "Dynamite" chip set. It meets or exceeds the requirements of the standards as specified in TS101 388, T1.413 and ETR328. It also provides BS EN60950 / IEC60950 / TS 001 / AS/NZS 3260 / CAN/ CSA C22.2 Np. 950-95 / UL1950 and CB Certificate supplementary insulation and UL Component Recognition (File No. E175058). * SCHEMATIC Pin (1-2) Pin (3-16) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 NOTES: TNV SELV Tip Ring Txp Txn A_Gnd_Tx N/C Hybrid Gnd Plane Rxp Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18 Rxn 8016 pin 4 / EL1510CS pin 3 8016 pin 2 / EL1510CS pin 1 8016 pin 3 / EL1510CS pin 2 N/C 8016 pin 21 / EL1510CS pin 5 8016 pin 23 / EL1510CS pin 7 8016 pin 22 / EL1510CS pin 6 N/C N/C ADI 8016 LINE DRIVER = 24 LEAD BATWING ELANTEC EL1510CS LINE DRIVER = 8 PIN SO 1. ALL TRACES BETWEEN APC PINS 10 AND 14 AND ADI LINE DRIVER PINS 4 AND 21 RESPECTIVELY, MUST BE KEPT SYMMETRICAL, PARALLEL AND EQUIDISTANT. 2. TWO 4.7NF PARALLEL CAPACITORS SHOULD BE PLACED BETWEEN ADI LINE DRIVER PIN 4 AND AGT (A_GND_TX) AND BETWEEN ADI LINE DRIVER PIN 21 AND AGT (A_GND_TX). THESE NEED TO BE PLACED AS CLOSE TO THE ADI LINE DRIVER AS POSSIBLE. SAFETY NOTE: THE CIRCUIT ON THE LC SIDE OF THE TRANSFORMER IS A SELV CIRCUIT AND THE CIRCUIT ON THE LINE SIDE OF THE TRANSFORMER IS A TNV CIRCUIT. - CIRCUITRY DESIGNATED AS SELV SHALL ONLY BE CONNECTED TO OTHER SELV CIRCUITS (UNDER NORMAL AND SINGLE FAULT CONDITIONS) IN END INSTALLATION - DO NOT PLACE HYBRID AGAINST OTHER COMPONENT PARTS ATTAINING EXCESSIVE TEMPERATURES. MECHANICAL 33 51.26 1 48.26 33.02 9 12 5.4 NOTES: NOT TO SCALE TOLERANCE +/- 0.2MM ALL DIMENSIONS IN MM PIN DIA. 0.75MM MAX. 29.7 18 2.54 10 (c)2003 Bel Fuse Inc. Specifications subject to change without notice. 05.20.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com Page 1 |
Price & Availability of APC78106
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |